Skip to content

Labels, printers and scanners

In Floormode, create label artwork once, then choose the paper and printer correction for each print run. Saving a design does not save its printer correction.

  • Set up a printer and medium
  • Print a PDF or send to a device
  • Barcode formats
  • GS1 prerequisites
  • A code that counts as several units
  • Check a new setup
  • Scan with a phone or tablet camera
  • Can’t scan? Take a photo
  • Weigh with a USB scale
  • Install Floormode on a phone or tablet
  • Carrier pickups
  • See also
  1. Open labels from the item list, locations or a receipt.
  2. Choose the paper format and label dimensions. Sheet labels have independent left, right, top and bottom margins. Thermal media can contain several labels across the roll.
  3. Open the calibration PDF and print at actual size / 100%. Disable the printer driver’s “fit to page” option.
  4. Measure the printed rulers and position. Adjust X/Y offset for position and X/Y scale for measured size. Save a profile with a recognizable printer and medium name, such as “Packing desk / 57 × 32 mm”.
  5. Print a small sample and scan it with the device used on the warehouse floor.

Profile names describe your setup. Direct printing separately selects a discovered PrintNode device. Changing a design keeps the current correction. If another user updates a profile, reload it explicitly to adopt the change.

The preview checks occupied space and barcode quiet zones. Rotation keeps the content’s dimensions; a rotation that does not fit is refused with guidance to reduce the element size or enlarge the medium. The final PDF checks actual font and barcode dimensions as well. Small media may fit a short identifier but not a long GS1-128 barcode. GS1 Data Matrix often uses less space.

Calibration proof sheets require a medium at least 20 × 20 mm. A legacy label without an explicit design conservatively reserves its entire label area, so some printer offsets are refused. Use a design with suitable artwork padding.

Preview & print PDF opens the authenticated PDF in either standalone or Shopify embedded access. Use the browser/PDF print controls to send it to a printer.

Direct printing uses the connected PrintNode account and a discovered device. The submitted PDF, printer and request identity are recorded before the provider call. “Sent” means PrintNode accepted the job; check the device for physical output. A timeout can mean that the provider accepted the job but its answer was lost. Check status and the printer before deliberately creating another attempt. Floormode does not automatically print a second copy after an uncertain result. The history keeps that job as unknown, including after background reconciliation. A confirmed provider refusal is failed. An expired worker also becomes unknown; it does not remain queued indefinitely. Request details report pending, accepted, refused or unknown separately from the background processing state.

Generated PDFs for direct printing are limited to 1 MiB. For larger sheets, select fewer labels or use the PDF flow. An old print request never prints again by itself; a new attempt records the previous request when one is supplied.

Automatic selection recognizes valid EAN-13, UPC-A and EAN-8 check digits and uses Code 128 for other supported printable identifiers. Explicit formats also include Code 39, ITF, UPC-E, QR Code, Data Matrix, PDF417, GS1-128 and GS1 Data Matrix.

ITF needs an even number of digits. UPC-E needs the full eight-digit compact code with its check digit. Some scanners expand UPC-E to UPC-A or EAN-13. Configure compact output, or add the exact expanded scanner output as an alternate item barcode. Printing never replaces the stored identifier.

The scanner reads GS1 codes in every common form: GS1-128, GS1 Data Matrix, GS1 DataBar and GS1 QR, the printed (01)…(17)…(10)… text, and GS1 Digital Link QR codes (https://…/01/<GTIN>/10/<lot>?17=…, any web address). It reads these application identifiers (AIs):

AI Value Handling
00 SSCC of a pallet or parcel Read. Scanned alone where an item is asked for, the floor says to scan the item’s barcode
01 GTIN of the item Finds the item by its barcode or an alternate barcode
02 GTIN of a carton’s contents Finds the item, like 01
10 Lot, up to 20 GS1 characters Capture at receiving; check allocated lot while picking
11, 13 Production and packaging date, YYMMDD Read, not booked
15 Best before, YYMMDD Read as the lot’s date when the code carries no 17; day 00 means month end
17 Expiry, YYMMDD Capture/check as a calendar date; day 00 means month end
21 Serial, up to 20 GS1 characters The unit’s serial for an item that tracks serials; refused on any other item
30 Variable count of items Read, not booked
37 Count of items in the carton Shown at receiving. You still book the units you count, unless the 02 GTIN is a code that counts as several units (below)
310n, 320n Net weight in kg (310n) or lb (320n), one weight; a label stating both is read in kg Read, not booked
330n, 340n Gross weight in kg (330n) or lb (340n), one weight; a label stating both is read in kg Read, not booked

Other AIs on a supplier’s label are skipped. A code that is broken, such as a wrong check digit, a cut-off value or a date that cannot exist, is refused, and the floor names the fault.

GTIN-13 and GTIN-14 match automatically: a GTIN-14 that starts with 0 finds the item whose barcode is the GTIN-13 (or UPC-A, or EAN-8), and the other way round. You do not need to add the 14-digit GTIN by hand. A case GTIN-14 that starts with 1–8 is the case’s own code and never finds the unit. The whole GS1 payload containing a lot or expiry is not an alternate item barcode.

Enable AIM symbology identifier transmission on the scanner: ]C1 for GS1-128 or ]d2 for GS1 Data Matrix. Also configure it to preserve the FNC1 separator between variable-length fields. Keyboard scanners can send ASCII 29 or Ctrl+]. An unmarked long numeric SKU or an ordinary web address is never guessed to be GS1. Repeated AIs are refused.

At receiving, enable lot tracking for the warehouse. Scanning fills the lot and expiry fields. Editing them to conflict with the barcode refuses the booking. Expiry-only data still needs a lot number. The current lot ledger uses uppercase keys without surrounding spaces; GS1 lot values requiring a different spelling are refused instead of silently changed. A serial (21) books the unit’s serial number for an item that tracks serials; on any other item the code is refused.

Picking checks scanned lot and expiry against the line’s allocated lot before moving stock. A task without an allocated lot cannot verify those attributes. Packing checks no lot, so its item scan refuses GS1 codes that carry a lot or expiry instead of claiming per-lot verification. Its serial step takes a code with a serial (21) whatever else it holds, without checking the lot or expiry. Other workflows without explicit GS1 lot handling also refuse structured booking. Read-only identification retains all supported fields.

For receiving-label designs, selecting a GS1 format combines an exact GTIN-14 with the movement’s captured lot and expiry. An explicitly supplied complete GS1 value is printed with its own fields. Month-end day 00 is rendered as the actual last calendar day; the date’s meaning is unchanged.

A supplier’s carton often has its own barcode. On the item page, open Barcodes, add the carton’s code and set Counts as to the units one carton holds, for example a carton of 12. One scan of that code then books 12 units at once:

  • Receive opens the quantity at 12 instead of what the line still owes. Each further scan of the same carton code adds 12. While filling a bin, each carton scan adds 12 and each unit scan adds 1.
  • Quick stock starts the quantity at 12, and each further scan of the carton adds 12.
  • Count opens the total at 12, and each further scan adds 12. You can type over it. The total you confirm replaces the earlier count, as always.
  • Pick and pack take units: a carton code is not the item there, and the scan says so as for any other code. Moves, transfers and Return to shelf only check the item, since the task carries the quantity.

The stock, movements and reservations always count single units. A GS1 label naming the carton’s GTIN in (01) books one carton; its (37) is shown and never multiplied. A label naming the contents (02) with a count (37) fills in the count times the carton’s units, for you to confirm.

Only your own codes can count as several units. A code that is also the item’s primary barcode, its SKU, or a code from Shopify or another app always counts as one unit. A carton code is never the code a tap sends, and an item that only a carton code finds is listed under Can’t be scanned. Serial items and items measured in weight, length or volume count every code as one unit. “Counts as” is not the Units per carton in the item’s dimensions, which is shelf capacity only.

A GS1 Digital Link web address stored as it reads, as a barcode, an alternate barcode or a SKU, finds its item as stored.

Print and scan representative identifiers, including the longest SKU, a lot with expiry and a dense matrix code. Confirm the returned identifier and attributes in the intended floor task. Repeat after changing the medium, printer driver, scanner output settings or scaling. PDF and independent decoder tests verify the software output; physical legibility depends on the actual equipment and stock.

No scanner at hand? Every floor task can scan with the device’s camera.

  1. Open the task in Floor Mode.
  2. Tap Scan with camera. Allow the camera when the browser asks.
  3. Hold the barcode inside the white frame. A short tick means the camera read it.
  4. Floormode answers the scan as it answers a scanner.

The camera reads EAN, UPC, Code 128, Code 39, QR and Data Matrix codes. It counts a label once while it stays in view. To scan the same label again, move the camera away for a moment, then back. Tap Light on in a dark aisle if your phone has a flashlight.

The camera turns off when you close it or switch to another app. If Floormode may not use the camera, allow it for this site in the browser settings.

Inside Shopify admin the camera may be blocked, or the button may not show. Open Floormode in its own browser tab or as the installed app instead.

A torn, faded or wrinkled label that no scanner reads still prints its code. With Read codes from a photo on (Settings › Picking & floor › Floor Mode, per warehouse, off by default), Floor Mode reads that printed code from a photo.

  1. On a bin or item step, open Scan with camera or Type code.
  2. Tap Can’t scan? Take a photo, hold the label inside the frame and tap Take the photo.
  3. Check the code Floor Mode read, then tap Use A-01-03. Nothing is booked before you tap it.

Check it: a code from a photo counts exactly like a typed one. A warehouse that asks for scans still asks a lead wherever it asks one for a typed code, and the desk’s summary of a pick list or parcel says “2 from a photo”. Floor Mode only uses a code that names one bin or one item. When two bins or items look alike (A-01-08 and A-01-0B, a barcode two items share), when the photo shows several codes, or when the bin belongs to another warehouse, it says so and you type the code.

A label without a readable code may still show the product’s name. Floor Mode then shows the items that look like it, but never books them: scan or type the item’s code. On Look up and on Today, tapping a bin or an item it found opens it there.

A cart slot, a serial number, a lot and a parcel’s seal are never read from a photo. A device without a camera shows no photo button.

The pack station can read the parcel weight from a USB scale, so nobody types it.

Which scales work: most USB shipping scales that need no extra software, such as Dymo M-series, Mettler Toledo PS-series and Stamps.com scales. Their manuals call them HID or point of sale scales.

Which browsers: Google Chrome or Microsoft Edge on a computer. Safari, Firefox, phones and tablets cannot read a scale. They keep the typed weight.

  1. Plug in the scale and switch it on.
  2. Open a parcel on the pack station.
  3. Click Connect scale under the weight field. Pick your scale in the list the browser shows.
  4. Put the parcel on the scale. When the weight settles, Floormode fills it in.
  5. Click Verify parcel or Save package as usual to keep the weight.

Floormode remembers the scale in this browser. Next time it connects by itself. If the scale switches itself off, switch it on again and Floormode reads it again.

A weight you typed is never replaced. Floormode shows Use scale weight instead, and you choose. The scale may show grams, kilograms, ounces or pounds. Floormode saves whole grams and shows the weight in the warehouse’s units: “2 lb 12 oz” in a warehouse on imperial units, “1,361 g” in a metric one.

Floormode also knows what the items and the box should weigh. When the scale differs by more than 15%, it asks you to check the parcel. You can still go on. This check needs a weight and dimensions on every item. Enter each box’s empty weight under Manage boxes too, or the box counts as weighing nothing.

Inside Shopify admin the browser may block the scale. Then the button does not show. Open Floormode in its own browser tab or as the installed app instead.

Installed, Floormode opens straight into Floor Mode, full screen, from the home screen.

  • iPhone or iPad (Safari): open Floormode, tap Share, then Add to Home Screen.
  • Android (Chrome): open Floormode, open the menu, then tap Install app or Add to Home screen.

The installed app uses your Floormode login, not Shopify admin. Sign in once in the app. It always loads the current version of Floormode, so there is nothing to update.

Shipping › Logistics books a carrier’s pickup (collection) at a warehouse, and shows each pickup with its status, number and fee.

  • Schedule pickup books the day’s open labels of the carrier at the warehouse; for a carrier with an end-of-day close-out it also closes them out. A manifest’s ⋯ menu books that manifest’s parcels.
  • The fee line says what a pickup costs: USPS is free; UPS shows its price and asks for your Max fee. Booked only if UPS’s quote is within your Max fee. UPS bills its own charge, which can be higher; a higher charge is flagged, never cancelled for you. Contract carriers charge under your contract, if at all. A carrier without a pickup API shows where to book it instead.
  • Cancel pickup cancels at the carrier; the row changes only on the carrier’s answer. When the carrier does not answer, the row says Cancellation not confirmed: check the carrier, then resolve it as cancelled or still booked. Reschedule cancels and books the same parcels again.
  • Pickup plans (per warehouse and carrier): When I ask, Regular pickup (the carrier comes on your contract’s daily pickup; nothing is booked) or Book at close-out (USPS: the close-out books the day’s pickup, or adds its parcels to the one already booked while its Collect by time is still 30 minutes away). A plan holds the window, the pickup contact (empty: the Shopify location’s) and where the parcels wait.
  • Owed by close-out is a booking a close-out made due before the carrier was asked: Book now, Book for another day or Drop it. A pickup the carrier missed is resolved as Not collected, then booked again.
Carrier Book Cancel Fee
UPS Floormode (live accounts once enabled) Floormode Booked only if UPS’s quote is within your Max fee. UPS bills its own charge; a higher charge is flagged, never cancelled for you.
USPS Floormode (live accounts once enabled) Floormode free
ShipEngine Floormode Floormode your carrier contract
CouriersPlease Floormode CouriersPlease account your contract
FedEx, DHL Paket, EasyPost, Sendcloud, Royal Mail, Evri, DPD UK, Australia Post, Aramex AU, GLS, DPD DE, DHL Express, Sendle the carrier’s account the carrier’s account the carrier’s